• Case: Lian-Li Pc-011 Dynamic Alpine White
• Cpu: Delidded 8700K @ 5.1ghz w/ EK velocity RGB clear CPU block
• Mobo: Asus Z370-E
• Memory: 4x8gb PC3600 TridentZ RGB
• GPU: 2x Asus Strix 1080TI OC w/ EK RGB GPU blocks
• Power Supply: Corsair HX1000i
• HDD1: 1x NVME M.2 960 Pro 500GB
• HDD2: 2x 850 pro SSD in Raid 0 = 500GB
• Corsair Commander Pro
Cooling
• *2x EK coolstream SE rads Side and Bottom
• 1x EK coolstream PE Rad Top
• EK FC Terminal X2 3 Slot Parallel Modded with extra port
• 1x EK xres/pump Combo w/ 250mm res
• 6x Corsair LL120 Fans
• 3x EK vardar Fans
• Barrow liquid temp monitor
• All EK and Darksider fittings
• EK Cryofuel Solid Azure Blue
Created Brackets off of the lower rad to support the GPU's then added a rail to the back of the case for the original PCI screws to thread into. The two PCI riser cards are floating due to the fitment of everything being so tight I had no way of keeping them totally locked in place as the cards need to drop down but then slide back when installed to clear the res.
I also had to modify the EK Terminal block to have a port coming in the Side of the block on both sides of it to keep the runs on the same plane. Flow does not seem to be bypassing second block as some people claim happens when the loop is done this way(Proved by Jayztwocents in a video that the flow will split between however many cards) and Cards stay @ 37 degrees while running Unigine for two hours.
CPU will max out at 65 degrees under full stress load and water temp generally equalizes at around 32 degrees.
• Cpu: Delidded 8700K @ 5.1ghz w/ EK velocity RGB clear CPU block
• Mobo: Asus Z370-E
• Memory: 4x8gb PC3600 TridentZ RGB
• GPU: 2x Asus Strix 1080TI OC w/ EK RGB GPU blocks
• Power Supply: Corsair HX1000i
• HDD1: 1x NVME M.2 960 Pro 500GB
• HDD2: 2x 850 pro SSD in Raid 0 = 500GB
• Corsair Commander Pro
Cooling
• *2x EK coolstream SE rads Side and Bottom
• 1x EK coolstream PE Rad Top
• EK FC Terminal X2 3 Slot Parallel Modded with extra port
• 1x EK xres/pump Combo w/ 250mm res
• 6x Corsair LL120 Fans
• 3x EK vardar Fans
• Barrow liquid temp monitor
• All EK and Darksider fittings
• EK Cryofuel Solid Azure Blue
Created Brackets off of the lower rad to support the GPU's then added a rail to the back of the case for the original PCI screws to thread into. The two PCI riser cards are floating due to the fitment of everything being so tight I had no way of keeping them totally locked in place as the cards need to drop down but then slide back when installed to clear the res.
I also had to modify the EK Terminal block to have a port coming in the Side of the block on both sides of it to keep the runs on the same plane. Flow does not seem to be bypassing second block as some people claim happens when the loop is done this way(Proved by Jayztwocents in a video that the flow will split between however many cards) and Cards stay @ 37 degrees while running Unigine for two hours.
CPU will max out at 65 degrees under full stress load and water temp generally equalizes at around 32 degrees.
Comment