Announcement

Collapse
No announcement yet.

Red & Black Frac (WIP)

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Red & Black Frac (WIP)

    Hello everyone, just wanted to share my first watercooled build. I'm far from new to IT world but have never dabbled into the watercooling before this.

    This build is not really new or the most powerful, but its more than enough for me.

    I don't pictures of every step of the way unfortunately but I plan to continually make changes to this machine and will keep this log updated with pictures as I go.

    System specs:
    Case - Fractal Design Define R4
    Motherboard - Asus Crosshair V Formula
    CPU - AMD FX8350
    RAM - 32GB DDR3 1600Mhz
    GPU - AMD 7950 (Have another I plan to eventually add into this build as well)
    HDD - 2x Kingston 64GB SSD (RAID 0)
    PSU - Corsair TX850 PSU

    Cooling setup:
    - DarkSide - Complete DUAL Radiator - D5 Vario Pump - Flex Kit
    - 240mm Darkside Performance Radiator
    - EK 7950 waterblock and backplate
    - Corsair SP120 fans x4 (soon to be x6)

    Planned changes:
    - Finish sleeving all cables in red
    - Squeeze in an additional slim 120mm Radiator beside PSU (if it does cramp up the case too much)
    - Change case light to red LED and link Power/HDD LED signals
    - Install additional 7950 GPU into loop
    - Setup white LED's inside the case
    - Full case side window
    - Replace black fan on back of case with AF140 (match the rest of the fans)
    - Cut out space on PSU cover for two temp sensors (CPU & GPU)
    - Cut out front grill fans (behind pull fans on front radiator) to allow for less obstructed airflow.

    I know the picture quality isnt the greatest but my celll phone camera is the only one I've got

    This is the first pic I have of this build



    This second pic has the following mods done:
    - Changed PSU to smaller TX850 I had from another system and installed covers over it and the drivebays
    - Front rad was installed higher to see if a 120mm rad would fit in the bottom near the PSU
    - Sleeved a few cables (few more to go)




    I welcome any suggestions or constructive criticism

  • #2
    Welcome to Dazmode Zone f_f

    nice and clean with the baymount res

    Darkside rad looks great!

    Comment


    • #3
      Damn! I wish my first build looked that neat! Nice job!

      Comment


      • #4
        Looking Good Fractal Fan.
        to the community.
        Blue Dragon CM690 II an i7 - 960 x58 build
        OverKill HTPC - Red Team Build an AMD FX6100 with dual HD 5870's in crossfire.
        Canadian Amateur Modding Competition

        Comment


        • #5
          Canadian CPU block!

          __________________________________________________
          Retro Build: Build Log,
          Baby Blue Build: Build Log,
          Green Lanten Build: Build Log,
          Sentinel Build: Build Log,
          Venom Build: Build Log,
          Silent Sniper Build: Final Video,
          Orange Build: Final Video
          HTPC Build: Final Video
          __________________________________________________

          Comment


          • #6
            Thanks everyone. Sorry the picture is not more clear, else everyone could see the maple leaf

            Comment


            • #7
              Love the Fractals ... we need more!
              +1 for Darkside Rad

              great job on the cover mods. really clean.

              just curious why you've got the GPU in the bottom slot?
              tell me its for aesthetics and/or easier tube route?

              either way, I like it mostly cause its in Mississauga!!
              HAF932 Mods
              C70 Mods

              Comment


              • #8
                Originally posted by bungwirez View Post
                great job on the cover mods. really clean.
                Thanks it took patience, plus trial and lots of error

                Originally posted by bungwirez View Post
                just curious why you've got the GPU in the bottom slot?
                tell me its for aesthetics and/or easier tube route?
                I put the GPU in that slot (not quite the bottom, one more PCIe slot under it) simply for aesthetics. I'm caught between moving up to something more powerful or adding in the second 7950 I have.

                Originally posted by bungwirez View Post
                either way, I like it mostly cause its in Mississauga!!
                Born and raised

                Comment


                • #9
                  Yup, four x 16 slots. Have the same board for my FX 8150.
                  3770K IHS removed-Max V gene-2x4gig ram Gskills 2400 Trident X-2x400watt Qmax TEC`s with dew point controller-420 Monsta rad for TEC hotside-360 TFC Xchanger for dual 670`s-RP452 res with 2xD5 vario pumps- HF Supreme with modified plate-DD Cp Pro pump for cold side of TEC and cpu block-Dual CM haf 922`s and a Seasonic X-1250 Psu

                  Comment


                  • #10
                    is it really 4x 16 slots? I didn't know for sure, guess then there's no performance compromise.
                    HAF932 Mods
                    C70 Mods

                    Comment


                    • #11
                      Originally posted by bungwirez View Post
                      is it really 4x 16 slots? I didn't know for sure, guess then there's no performance compromise.
                      From what I understand it is 4x PCIe x16 slots but actual speed the slot runs at depends on what is installed in all the other slots.

                      The first PCI Express x16 slot (PCIE_X16_1) always runs at x16 speed; the second PCI Express x16 slot (PCIE_X8/X1_2) always runs at x8 speed; the third PCI Express x16 slot (PCIE_X16/X8_3) runs at x16 speed when the second PCI Express x16 slot is empty or at x8 speed when this other slot is used; and the fourth PCI Express x16 slot (PCIE_X4_4) always runs at x4 speed. This way, in order to achieve the best performance if you are installing two video cards, you should install them in the first and third slots, not in the first and second slots as it would appear more logical
                      Pulled that info from here

                      So having my card in that slot should have no effect on performance

                      Comment


                      • #12
                        Nice system. Good to see someone with Fractal case here, welcome to the club!

                        Comment


                        • #13
                          Looks beautiful great job man
                          Dragon Azul Build
                          Case: NZXT Switch 810 | AsROCK Extreme4 z77 1155 | i5 3570K OC @ 4.6Ghz | GPU: EVGA GTX 660 Ti 3GB SC+ | Corsair Dominator 1600Mhz 16GB | Corsair AX850w | SSD: Corsair 120GB FORCE 3 | HDD: 1TB WD Caviar Blue | Soundcard: Soundblaster RECON 3D

                          Comment


                          • #14
                            Can anyone tell me which interconnect I should get for adding in my second GPU (another 7950)? I plan to install them in the top two x16 slots so there will be a gap of one slot inbetween them. I think a serial interconnect is the one I want.

                            I've been looking through the store but don't want to get something that won't fit or work.

                            Thanks in advance

                            Comment


                            • #15
                              Should probably mention the waterblock I'm using for the GPU is here

                              Comment

                              Working...
                              X